System Integration Engineering
From Standalone Subsystems to a Functioning Automated Cell
System integration connects mechanical actuators, servo drives, robot controllers, safety systems, sensors, and plant-level supervisory controls into a single deterministic production system. INDUS engineering engagements define mechanical, electrical, and control boundaries before hardware commitment.
Engineering Scope
Defining System Boundaries Before Integration
Clear boundary definition is the first integration step. Each subsystem — robot controller, servo drive, safety PLC, HMI, and plant MES — has defined input/output interfaces, signal ownership, and timing responsibilities.
Mechanical Boundary
Mounting interfaces, load paths, cable routing envelope, maintenance clearances, and thermal dissipation zones.
Electrical Boundary
Power distribution, cabinet earthing, cable segregation (power vs signal), connector standards, and IP rating compliance.
Control Boundary
Fieldbus master/slave topology, cyclic I/O mapping, process data objects, safety channel wiring, and emergency stop circuit architecture.
Communication Architecture
Supported Fieldbus Topologies & Control Layers
Industrial fieldbuses carry deterministic cyclic process data between controllers and drives. The choice of protocol depends on controller OEM, required cycle time, network topology, and installed equipment.
EtherCAT
Sub-millisecond distributed clock synchronization (DC). Used for high-axis-count multi-robot cells. Line or ring topology.
PROFINET IRT
Isochronous real-time profile. Common in Siemens-ecosystem plants. Supported by most major drive manufacturers.
EtherNet/IP
CIP protocol. Common in Rockwell Automation environments. Suitable for motion and I/O integration.
CANopen / DeviceNet
Older installed-base protocols. Lower bandwidth; suitable for low-axis-count or legacy machine retrofit.
Protocol Compatibility Note: Protocol compatibility depends on the specific robot controller, drive, and safety PLC combination selected for the project. INDUS engineers verify protocol support during the Define phase.
Integration Architecture
Typical Integration Components
Robot Controller
Motion programming, kinematic model
Servo Drive Network
Axis torque/velocity loops
Safety PLC
Emergency stop, STO, zone management
HMI / Operator Panel
Recipe management, alarm display
Sensors & Vision
Trigger, result, coordinate handshake
Plant MES / SCADA
Production orders, batch data, OEE
Signal & Sequence Requirements
Typical signals managed across the integration boundary:
- Digital I/O handshakes
- Robot program start/stop
- Conveyor interlock
- Vision trigger/result
- Safety door monitoring
- Fault annunciation
Retrofit Integration
Legacy Machine Integration Considerations
Existing production lines often contain legacy PLCs, proprietary serial protocols, and non-standard signal conditioning. Integration projects require interface documentation, protocol conversion, and signal isolation before new automation hardware is installed.
- 01
Obtain existing wiring schematics and PLC program documentation.
- 02
Identify non-standard signal voltages, loop currents, and serial baud rates.
- 03
Define gateway or protocol converter requirements and validate timing budgets.
Project Execution
Integration Testing & Commissioning Sequence
FAT
Factory Acceptance Test
Individual subsystem verification at supplier facility. Axis homing, safety circuit continuity, network communication, and motion profile validation.
Pre-SAT
Installation Readiness
Mechanical alignment, cable routing, earthing continuity, and cabinet thermal verification at customer site before power-on.
SAT
Site Acceptance Test
Full system power-on sequence, coordinated motion routines, I/O handshake verification, and alarm response testing.
Handover
Handover
Operator training, validated backup of all controller projects, as-built documentation, and agreed preventive maintenance schedule.
Start an Integration Discussion
Define Your System Integration Scope
Share your existing equipment inventory, fieldbus preferences, safety category requirements, and production throughput targets. Our integration engineers will define the interface architecture and project milestones.
Connected Ecosystem
Related Engineering Content
Engineering Services
- Engineering CapabilitiesEngineering Services
Overview of INDUS engineering disciplines: application feasibility, mechatronics, workcells, motion control, safety, and lifecycle optimization.
- Kinematic Sizing CalculatorsTechnology
Interactive tools for sizing joints, drives, and reducers based on your application torque, speed, and inertia targets.
- Technical SpecificationsEngineering Reference
Specification reference for INDUS product families: torque, speed, payload, repeatability, fieldbus, and environmental limits.